Active Unanswered
Connie Refresh
Moderators: Don Ayers, Al Benton, Don Vogt
Re: Connie Refresh
Great to see this!! I’ve been contemplating such a thing my self. Just checked out an aluminum carport type structure. I think I can build one myself for about half that cost.
Bill Hammond
1960 36' Connie
Flint/Port Huron, MI
http://www.chris-craft.org/registry/vie ... at_id=1708
1960 36' Connie
Flint/Port Huron, MI
http://www.chris-craft.org/registry/vie ... at_id=1708
Re: Connie Refresh
I put a similar cover on the pier over "Lucky 7" My U-22. Amazing the difference it made.
Jim Staib
www.finewoodboats.com
1947 Penn Yan 12' Cartopper WXH474611
1950 Chris-Craft 22' Sportsman U-22-1532
1957 Chris-Craft 26' Sea Skiff SK-26-515
1968 Century 17' Resorter FG-68-174
www.finewoodboats.com
1947 Penn Yan 12' Cartopper WXH474611
1950 Chris-Craft 22' Sportsman U-22-1532
1957 Chris-Craft 26' Sea Skiff SK-26-515
1968 Century 17' Resorter FG-68-174
-
- Posts: 2092
- Joined: Thu Dec 29, 2005 10:41 pm
- Location: Powhatan Courthouse Virginia
- Contact:
Re: Connie Refresh
yep, being in a covered slip saves my Fairchild scout.
John in VA
John in VA
1980 Fairchild Scout 30
19?? custom Argentine Runabout 16'
1954 Whirlwind deluxe dual ckpt 16'
1921 Old Town Charles River 17' (founding Captain, James River Batteau Festival)
19?? custom Argentine Runabout 16'
1954 Whirlwind deluxe dual ckpt 16'
1921 Old Town Charles River 17' (founding Captain, James River Batteau Festival)
Re: Connie Refresh
I remember seeing something about the system you’re using before. Can you tell us something about it, Troy?
Bill Hammond
1960 36' Connie
Flint/Port Huron, MI
http://www.chris-craft.org/registry/vie ... at_id=1708
1960 36' Connie
Flint/Port Huron, MI
http://www.chris-craft.org/registry/vie ... at_id=1708
Re: Connie Refresh
Gladly!
If you look back at the first page of this thread you will find that Peter Jardine referred to this type of building as a Stimson Bow Shed.
What we did was create a jig on a full piece of plywood. Using 1X4 green hemlock we bent the boards on the jig and placed 2X4 blocking in between the boards with decking screws to hold the shape. (We found that planing the boards down some helped us bend the boards without having them break. They would usually break where any knots were of course.)
Once all the frames were made we stood one up over the boat to determine the angle that we needed to cut at the top of the frames. We would then connect two or three frames to a 2X6 ridge pole and raise the section up over the boat, holding it in place while raising the adjoining frames on the other side of the boat and attaching them to the same ridge pole. Once a few frames were attached it was quite simple and easy to continue attaching the rest. We used 4 people and a man lift to accomplish this task.
After the frame work was complete we used "Shrink Wrap" to enclose the shed placing foam padding at any chafe point concerns. I chose clear shrink wrap to allow light into the shed as well as viewing exposure since American Beauty is for sale and she is stored on a very busy road. Once she moves on to a new steward I should be able to use this building for my other boats for many years.
If I were building a shed for a smaller boat I would consider using basic 1.5" strapping and placing the frames closer together.
Good Luck!
If you look back at the first page of this thread you will find that Peter Jardine referred to this type of building as a Stimson Bow Shed.
What we did was create a jig on a full piece of plywood. Using 1X4 green hemlock we bent the boards on the jig and placed 2X4 blocking in between the boards with decking screws to hold the shape. (We found that planing the boards down some helped us bend the boards without having them break. They would usually break where any knots were of course.)
Once all the frames were made we stood one up over the boat to determine the angle that we needed to cut at the top of the frames. We would then connect two or three frames to a 2X6 ridge pole and raise the section up over the boat, holding it in place while raising the adjoining frames on the other side of the boat and attaching them to the same ridge pole. Once a few frames were attached it was quite simple and easy to continue attaching the rest. We used 4 people and a man lift to accomplish this task.
After the frame work was complete we used "Shrink Wrap" to enclose the shed placing foam padding at any chafe point concerns. I chose clear shrink wrap to allow light into the shed as well as viewing exposure since American Beauty is for sale and she is stored on a very busy road. Once she moves on to a new steward I should be able to use this building for my other boats for many years.
If I were building a shed for a smaller boat I would consider using basic 1.5" strapping and placing the frames closer together.
Good Luck!
Troy in ANE - Former President CCABC
1957 CC 21' Continental "Yorktown" (Mom's boat)
https://www.chris-craft.org/boats/22625/
1985 Formula 242LS "Gottago"
1991 Formula 36PC "Band Aids"
Life Is Too Short To Own An Ugly Boat
1957 CC 21' Continental "Yorktown" (Mom's boat)
https://www.chris-craft.org/boats/22625/
1985 Formula 242LS "Gottago"
1991 Formula 36PC "Band Aids"
Life Is Too Short To Own An Ugly Boat
Re: Connie Refresh
American Beauty has moved on to a new Steward.
Troy in ANE - Former President CCABC
1957 CC 21' Continental "Yorktown" (Mom's boat)
https://www.chris-craft.org/boats/22625/
1985 Formula 242LS "Gottago"
1991 Formula 36PC "Band Aids"
Life Is Too Short To Own An Ugly Boat
1957 CC 21' Continental "Yorktown" (Mom's boat)
https://www.chris-craft.org/boats/22625/
1985 Formula 242LS "Gottago"
1991 Formula 36PC "Band Aids"
Life Is Too Short To Own An Ugly Boat
- Captain Nemo
- Posts: 733
- Joined: Tue Jul 07, 2009 7:40 pm
- Location: Lyons, NY
- Contact:
Re: Connie Refresh
I hope she found a very good home. Troy, as you know, the day you buy a boat and the day you sell are the best days of your life. I hope you’re not going to be a stranger around here now.
Boats are to be made of wood, otherwise, God would have grown fiberglass trees.
Re: Connie Refresh
Thanks Nemo!
I will still be lurking around. I continue to have the honor of caring for Yorktown, the Chris-Craft my parents purchased when I was only 2 1/2 years old. She is truly a member of the family.
I will admit my passion and focus have turned to longer cruising and one day doing The Loop.
I will still be lurking around. I continue to have the honor of caring for Yorktown, the Chris-Craft my parents purchased when I was only 2 1/2 years old. She is truly a member of the family.
I will admit my passion and focus have turned to longer cruising and one day doing The Loop.
Troy in ANE - Former President CCABC
1957 CC 21' Continental "Yorktown" (Mom's boat)
https://www.chris-craft.org/boats/22625/
1985 Formula 242LS "Gottago"
1991 Formula 36PC "Band Aids"
Life Is Too Short To Own An Ugly Boat
1957 CC 21' Continental "Yorktown" (Mom's boat)
https://www.chris-craft.org/boats/22625/
1985 Formula 242LS "Gottago"
1991 Formula 36PC "Band Aids"
Life Is Too Short To Own An Ugly Boat
- Captain Nemo
- Posts: 733
- Joined: Tue Jul 07, 2009 7:40 pm
- Location: Lyons, NY
- Contact:
Re: Connie Refresh
I forgot about Yorktown. Enjoy!
Boats are to be made of wood, otherwise, God would have grown fiberglass trees.
Who is online
Users browsing this forum: No registered users and 5 guests