hello help needed i have a 283 fly wheel forward motor. the port motor too be exacte i have put new heads on it three times in the last year and with in 3 hour it cracks the head between the center cyl. what is the firing order on it first ? where is the # 1 cyl. ??? is there a differance in the fly...

thanks i will try that combo last time i tryed it it would not start . i will let you guys know .
thanks steve

can someone email me or post here a page out of a manual that shows the # 1 cylinder location on the port motor with fireing order . it's a 1965 30' constellation. thanks steve
pm me for my email
thanks again

have you tryed mississippi river boat works in rock island
not sure if they do that work or not
or try island marina in east moline

i have called them in the last two months two times and both times i call at the time they open and got right through . and both times got what i was looking for faster than if i faxed it ! maybe try that it works for me, never had to leave a message

hope that helps steve

hello i got a few thousand from
wolf's marine in benton harbor mi.
a few years ago
hope this helps let me know if you need more help with this . i did have web site for them but it will not come up now .
thanks steve

i have a old trailer that i was told it was from early 40s or earler that i got with my 1938 or 39 runabout . i say that because on the hull card it says in was delivered in jan. of 1939 so it had to be built in 1938 . but i am out of town for a month or so and can't get any pictures of it right now...

hello can any body tell me the title of a good book that covers lofting?
i just got my table of offsets from mariners and i am trying to make sense of it ! so i can check all the mensurments.
i can't find any topics on it at all.
any help would be great
thanks steve

LL johnson lumber mfg. co.
563 n. cochran ave.
charlotte mi. 48813
1-800-292-5937
they will have any wood you will need. not sure where you are but they also have a store in south bend in.219-277-8350
they can also resaw the planks for you !!
hope this helps steve

hello maybee someone can list a table off from another boat that way i can see what reference points they are talking about. and see if there is a way to get these measurments from a boat that has been restored .
any help would be great

thanks steve

hello i am working on a 1939 15 1/2' deluxe runabout hull # 52136
i need a table of offsets for this boat dose anybody have these i can buy or get a copy of????
thanks in advance steve

thanks bill i was looking for something smaller.
just put in 25.00
thanks again

steve

how and where do i feed the fund

birrellsa
here is a picture of the puller i use to remove that gear hope it helps.
it's a bit__ [/list]

hello paul i have a 30' constallation with 283 fly wheel forward motors . where can i find the impellers for the older style pumps you talked about also the cams and thermostats for these.one pump has the fin type impellers the other has the round type impellers. any help would be great !!!!!!! than...

hello in the chris craft essential guide it shows there were 29 1953 52'ers built hull # cc-52-001 to cc-52-029 in 1954 through 1955 there were 26 hulls built that were called 53'ers hull #s c-53-001 to c-53-026 hope this helps niether shows with hard top you will have to get hull card for the optio...

hello you can try LL Johnson lumber mfg co. they are in charlotte mi.
http://www.theworkbench.com/index.php
this link should get you there .
hope this helps

a little mach. shop in low moor iowa.
they were 80.00 each if you want more info about the shop let me know thanks

hello i just had two of them made also i was told by the shop that if i had them fixed they would be weak and twist or rebend . hope this helps

hello i just had two made then i saw some in the classic boat conections catalog.
i had them made for less than they sell them for. there on page 18 hope this helps.

hello what is a good source for new shaft logs ? or even used ones !
its for a 30' chris craft its 18" long 3 1/2" wide for 1 1/4 shaft
1 1/2" id 1 3/4" od
15 deg.
casting # is 1222
any help is great
thanks

yzer go to stains, sealer, varnishs
there is pictures of how mine turned out .

heres more thanks for all your responces

if i can do this right heres some pictures of the transom

thanks all it's done i will post pictures soon . it turned out good enough first one , good practice for the other one !

thanks al they are both petit, clear sealer ,and petit bark v spar varnish i thought i would let the last coat of sealant dry and extra 8 to 10 houres before i sand then start the varnish.


thanks for the help steve

hello I am in the process of restaining ,sealing,
varnishing the transom on my 30' conie. Got it sanded down and stained. Is there anything i need to do to the stain before i start puting the sealer on ?
please any help is greatly appreciated
thanks steve

thanks bill i will be waiting for it !!

please let us know when it comes out !!!!

thanks again steve

i ment do you guys have any other videos for sell?



thanks again steve

Bill i have not got a email so here is my email add. spwtrboys@aol.com . by the way i got that vidio from you the 1929 cc vidio it is way to cool it is so good i had to watch it over two more times. It's to good do you guys have any other dvds like that ? thanks for all your hard work !!!!!!!!!! my ...