Active Unanswered
Self bailer vent hole
Moderators: Don Ayers, Al Benton, Don Vogt
Self bailer vent hole
Am installing the original self bailer on a '38 CC deluxe runabout. It has a shut off valve installed which I intend to keep closed for safety. ( I will also have a new bilge pump installed.) I just want it to look original, even though the bailer will not be operational normally. Question is, if I ever need to actually use it , it doesn't seem to have the tiny vent hole in the top to prevent siphoning. Wasn't that required for proper operation? Should I add a vent hole? What size would it have been?
'38 Chris Craft Deluxe Runabout 17'
'58 Century Raven 22'
'35 Old Town Canoe 16'
'65 Chestnut Canoe 16'
'58 Century Raven 22'
'35 Old Town Canoe 16'
'65 Chestnut Canoe 16'
- Captain Nemo
- Posts: 733
- Joined: Tue Jul 07, 2009 7:40 pm
- Location: Lyons, NY
- Contact:
Re: Self bailer vent hole
I would drill the hole in it in case you forget to shut off the valve. It will operate without the siphon break, but for safety you should drill it out. It is a small hole, 1/16 maybe?
Boats are to be made of wood, otherwise, God would have grown fiberglass trees.
Re: Self bailer vent hole
Thanks Captain.
'38 Chris Craft Deluxe Runabout 17'
'58 Century Raven 22'
'35 Old Town Canoe 16'
'65 Chestnut Canoe 16'
'58 Century Raven 22'
'35 Old Town Canoe 16'
'65 Chestnut Canoe 16'
Re: Self bailer vent hole
self bailers can be dangerous. I had mine reinstalled for the look ( I tried to include a photo but the system still isnt working to upload pictures). it was made inoperable. Too many horror stories of boats sinking via the bailer. looked it over this morning but couldnt find the hole. perhaps it was closed off when they reinstalled. It is quite small as i recall.
1938 Chris Craft 17' Deluxe Runabout "Jennifer II"
Re: Self bailer vent hole
You can tap the inside hole of the bailer with a 1/2 inch pipe tap. Then install a brass pipe plug with JB Weld on the threads. Then put the hose and bailer on. Done this way it will look completely original.
It should have a hole at the very top of the loop. smaller then a 1/16 inch. If the hole is to big it will never create suction.
Also there were some self bailers that Chris Craft used were the loop parts was a casted piece and the brass pipe clamp into it. On these there is a slot were the copper pipe clamps into the casted piece that creates the suction break. So this style does not have a small hole drilled in them.
It should have a hole at the very top of the loop. smaller then a 1/16 inch. If the hole is to big it will never create suction.
Also there were some self bailers that Chris Craft used were the loop parts was a casted piece and the brass pipe clamp into it. On these there is a slot were the copper pipe clamps into the casted piece that creates the suction break. So this style does not have a small hole drilled in them.
Re: Self bailer vent hole
Thanks Jim. I think this is the style I have, with no hole and cast clamp.
'38 Chris Craft Deluxe Runabout 17'
'58 Century Raven 22'
'35 Old Town Canoe 16'
'65 Chestnut Canoe 16'
'58 Century Raven 22'
'35 Old Town Canoe 16'
'65 Chestnut Canoe 16'
Who is online
Users browsing this forum: No registered users and 3 guests